Other FIPS approved cryptographic algorithms may be used in addition to, or in lieu of, this standard when implemented in accordance with FIPS 140-1.
In addition, this standard may be adopted and used by non-Federal Government organizations. Such use is encouraged when it provides the desired security for commercial and private organizations.
7. Applications. Data encryption (cryptography) is utilized in various applications and environments. The specific utilization of encryption and the implementation of the DES will be based on many factors particular to the computer system and its associated components. In general, cryptography is used to protect data while it is being communicated between two points or while it is stored in a medium vulnerable to physical theft. Communication security provides protection to data by enciphering it at the transmitting point and deciphering it at the receiving point. File security provides protection to data by enciphering it when it is recorded on a storage medium and deciphering it when it is read back from the storage medium. In the first case, the key must be available at the transmitter and receiver simultaneously during communication. In the second case, the key must be maintained and accessible for the duration of the storage period. FIPS 171 provides approved methods for managing the keys used by the algorithm specified in this standard.
8. Implementations. Cryptographic modules which implement this standard shall conform to the requirements of FIPS 140-1. The algorithm specified in this standard may be implemented in software, firmware, hardware, or any combination thereof. The specific implementation may depend on several factors such as the application, the environment, the technology used, etc. Implementations which may comply with this standard include electronic devices (e.g., VLSI chip packages), micro-processors using Read Only Memory (ROM), Programmable Read Only Memory (PROM), or Electronically Erasable Read Only Memory (EEROM), and mainframe computers using Random Access Memory (RAM). When the algorithm is implemented in software or firmware, the processor on which the algorithm runs must be specified as part of the validation process. Implementations of the algorithm which are tested and validated by NIST will be considered as complying with the standard. Note that FIPS 140-1 places additional requirements on cryptographic modules for Government use. Information about devices that have been validated and procedures for testing and validating equipment for conformance with this standard and FIPS 140-1 are available from the National Institute of Standards and Technology, Computer Systems Laboratory, Gaithersburg, MD 20899.
9. Export Control. Cryptographic devices and technical data regarding them are subject to Federal Government export controls as specified in Title 22, Code of Federal Regulations, Parts 120 through 128. Some exports of cryptographic modules implementing this standard and technical data regarding them must comply with these Federal regulations and be licensed by the U.S. Department of State. Other exports of cryptographic modules implementing this standard and technical data regarding them fall under the licensing authority of the Bureau of Export Administration of the U.S. Department of Commerce. The Department of Commerce is responsible for licensing cryptographic devices used for authentication, access control, proprietary software, automatic teller machines (ATMs), and certain devices used in other equipment and software. For advice concerning which agency has licensing authority for a particular cryptographic device, please contact the respective agencies.
10. Patents. Cryptographic devices implementing this standard may be covered by U.S. and foreign patents issued to the International Business Machines Corporation. However, IBM has granted nonexclusive, royalty-free licenses under the patents to make, use and sell apparatus which complies with the standard. The terms, conditions and scope of the licenses are set out in notices published in the May 13, 1975 and August 31, 1976 issues of the Official Gazette of the United States Patent and Trademark Office (934 O.G. 452 and 949 O.G. 1717).
11. Alternative Modes of Using the DES. FIPS PUB 81, DES Modes of Operation, describes four different modes for using the algorithm described in this standard. These four modes are called the Electronic Codebook (ECB) mode, the Cipher Block Chaining (CBC) mode, the Cipher Feedback (CFB) mode, and the Output Feedback (OFB) mode. ECB is a direct application of the DES algorithm to encrypt and decrypt data; CBC is an enhanced mode of ECB which chains together blocks of cipher text; CFB uses previously generated cipher text as input to the DES to generate pseudorandom outputs which are combined with the plaintext to produce cipher, thereby chaining together the resulting cipher; OFB is identical to CFB except that the previous output of the DES is used as input in OFB while the previous cipher is used as input in CFB. OFB does not chain the cipher.
12. Implementation of this standard. This standard became effective July 1977. It was reaffirmed in 1983, 1988, and 1993. It applies to all Federal agencies, contractors of Federal agencies, or other organizations that process information (using a computer or telecommunications system) on behalf of the Federal Government to accomplish a Federal function. Each Federal agency or department may issue internal directives for the use of this standard by their operating units based on their data security requirement determinations. FIPS 46-2 which revises the implementation of the Data Encryption Algorithm to include software, firmware, hardware, or any combination thereof, is effective June 30, 1994. This revised standard may be used in the interim period before the effective date.
NIST provides technical assistance to Federal agencies in implementing data encryption through the issuance of guidelines and through individual reimbursable projects. The National Security Agency assists Federal departments and agencies in communications security for classified applications and in determining specific security requirements. Instructions and regulations for procuring data processing equipment utilizing this standard are included in the Federal Information Resources Management Regulation (FIRMR) Subpart 201-8.111-1.
13. Specifications. Federal Information Processing Standard (FIPS) 46-2, Data Encryption Standard (DES) (affixed).
14. Cross Index.
- a. Federal Information Resources Management Regulations (FIRMR) subpart 201.20.303, Standards, and subpart 201.39.1002, Federal Standards.
- b. FIPS PUB 31, Guidelines to ADP Physical Security and Risk Management.
- c. FIPS PUB 41, Computer Security Guidelines for Implementing the Privacy Act of 1974.
- d. FIPS PUB 65, Guideline for Automatic Data Processing Risk Analysis.
- e. FIPS PUB 73, Guidelines for Security of Computer Applications.
- f. FIPS PUB 74, Guidelines for Implementing and Using the NBS Data Encryption Standard.
- g. FIPS PUB 81, DES Modes of Operation.
- h. FIPS PUB 87, Guidelines for ADP Contingency Planning.
- i. FIPS PUB 112, Password Usage.
- j. FIPS PUB 113, Computer Data Authentication.
- k. FIPS PUB 140-1, Security Requirements for Cryptographic Modules.
- l. FIPS PUB 171, Key Management Using ANSI X9.17.
- m. Other FIPS and Federal Standards are applicable to the implementation and use of this standard. In particular, the Code for Information Interchange, Its Representations, Subsets, and Extensions (FIPS PUB 1-2) and other related data storage media or data communications standards should be used in conjunction with this standard. A list of currently approved FIPS may be obtained from the National Institute of Standards and Technology, Computer Systems Laboratory, Gaithersburg, MD 20899.
15. Qualifications. The cryptographic algorithm specified in this standard transforms a 64-bit binary value into a unique 64-bit binary value based on a 56-bit variable. If the complete 64-bit input is used (i.e., none of the input bits should be predetermined from block to block) and if the 56-bit variable is randomly chosen, no technique other than trying all possible keys using known input and output for the DES will guarantee finding the chosen key. As there are over 70,000,000,000,000,000 (seventy quadrillion) possible keys of 56 bits, the feasibility of deriving a particular key in this way is extremely unlikely in typical threat environments. Moreover, if the key is changed frequently, the risk of this event is greatly diminished. However, users should be aware that it is theoretically possible to derive the key in fewer trials (with a correspondingly lower probability of success depending on the number of keys tried) and should be cautioned to change the key as often as practical. Users must change the key and provide it a high level of protection in order to minimize the potential risks of its unauthorized computation or acquisition. The feasibility of computing the correct key may change with advances in technology.
A more complete description of the strength of this algorithm against various threats is contained in FIPS PUB 74, Guidelines for Implementing and Using the NBS Data Encryption Standard.
When correctly implemented and properly used, this standard will provide a high level of cryptographic protection to computer data. NIST, supported by the technical assistance of Government agencies responsible for communication security, has determined that the algorithm specified in this standard will provide a high level of protection for a time period beyond the normal life cycle of its associated equipment. The protection provided by this algorithm against potential new threats will be reviewed within 5 years to assess its adequacy (See Special Information Section). In addition, both the standard and possible threats reducing the security provided through the use of this standard will undergo continual review by NIST and other cognizant Federal organizations. The new technology available at that time will be evaluated to determine its impact on the standard. In addition, the awareness of any breakthrough in technology or any mathematical weakness of the algorithm will cause NIST to reevaluate this standard and provide necessary revisions.
At the next review (1998), the algorithm specified in this standard will be over twenty years old. NIST will consider alternatives which offer a higher level of security. One of these alternatives may be proposed as a replacement standard at the 1998 review.
16. Comments. Comments and suggestions regarding this standard and its use are welcomed and should be addressed to the National Institute of Standards and Technology, Attn: Director, Computer Systems Laboratory, Gaithersburg, MD 20899.
17. Waiver Procedure. Under certain exceptional circumstances, the heads of Federal departments and agencies may approve waivers to Federal Information Processing Standards (FIPS). The head of such agency may redelegate such authority only to a senior official designated pursuant to section 3506(b) of Title 44, United States Code. Waiver shall be granted only when:
- a. Compliance with a standard would adversely affect the accomplishment
of the mission of an operator of a Federal computer system; or
- b. Compliance with a standard would cause a major adverse financial impact on the operator which is not offset by Government-wide savings.
In addition, notice of each waiver granted and each delegation of authority to approve waivers shall be sent promptly to the Committee on Government Operations of the House of Representatives and the Committee on Government Affairs of the Senate and shall be published promptly in the Federal Register.
When the determination on a waiver applies to the procurement of equipment and/or services, a notice of the waiver determination must be published in the Commerce Business Daily as a part of the notice of solicitation for offers of an acquisition or, if the waiver determination is made after that notice is published, by amendment to such notice.
A copy of the waiver, any supporting documents, the document approving the waiver and any accompanying documents, with such deletions as the agency is authorized and decides to make under 5 United States Code Section 552(b), shall be part of the procurement documentation and retained by the agency.
18. Special Information. In accordance with the Qualifications Section of this standard, reviews of this standard have been conducted every 5 years since its adoption in 1977. The standard was reaffirmed during each of those reviews. This revision to the text of the standard contains changes which allow software implementations of the algorithm and which permit the use of other FIPS approved cryptographic algorithms.
19. Where to Obtain Copies of the Standard. Copies of this publication are for sale by the National Technical Information Service, U.S. Department of Commerce, Springfield, VA 22161. When ordering, refer to Federal Information Processing Standards Publication 46-2 (FIPS PUB 46-2), and identify the title. When microfiche is desired, this should be specified. Prices are published by NTIS in current catalogs and other issuances. Payment may be made by check, money order, deposit account or charged to a credit card accepted by NTIS.
FIPS PUB 44-2
Supersedes FIPS PUB 46-1
1988 January 22
Processing Standards Publication 46-2
1993 December 30
DATA ENCRYPTION STANDARD
The Data Encryption Standard (DES) shall consist of the following Data Encryption Algorithm to be implemented in special purpose electronic devices. These devices shall be designed in such a way that they may be used in a computer system or network to provide cryptographic protection to binary coded data. The method of implementation will depend on the application and environment. The devices shall be implemented in such a way that they may be tested and validated as accurately performing the transformations specified in the following algorithm.
Introduction
The algorithm is designed to encipher and decipher blocks of data consisting of 64 bits under control of a 64-bit key.** Deciphering must be accomplished by using the same key as for enciphering, but with the schedule of addressing the key bits altered so that the deciphering process is the reverse of the enciphering process. A block to be enciphered is subjected to an initial permutation IP, then to a complex key-dependent computation and finally to a permutation which is the inverse of the initial permutation IP-1. The key-dependent computation can be simply defined in terms of a function f, called the cipher function, and a function KS, called the key schedule. A description of the computation is given first, along with details as to how the algorithm is used for encipherment. Next, the use of the algorithm for decipherment is described. Finally, a definition of the cipher function f is given in terms of primitive functions which are called the selection functions Si and the permutation function P. Si, P and KS of the algorithm are contained in the Appendix.
The following notation is convenient: Given two blocks L and
R of bits, LR denotes the block consisting of the bits of
L followed by the bits of R. Since concatenation is associative,
B1B2...B8, for example,
denotes the block consisting of the bits of B1
followed by the bits of B2...followed by the
bits of B8.
** Blocks are
composed of bits numbered from left to right, i.e., the left most bit of a
block is bit one.
, Data Encryption Standard_files/fip46-1.gif)
Figure 1. Enciphering computation.
Enciphering
A sketch of the enciphering computation is given in Figure 1.
The 64 bits of the input block to be enciphered are first subjected to the following permutation, called the initial permutation IP:
IP 58 50 42 34 26 18 10 2 60 52 44 36 28 20 12 4 62 54 46 38 30 22 14 6 64 56 48 40 32 24 16 8 57 49 41 33 25 17 9 1 59 51 43 35 27 19 11 3 61 53 45 37 29 21 13 5 63 55 47 39 31 23 15 7
That is the permuted input has bit 58 of the input as its first bit, bit 50 as its second bit, and so on with bit 7 as its last bit. The permuted input block is then the input to a complex key-dependent computation described below. The output of that computation, called the preoutput, is then subjected to the following permutation which is the inverse of the initial permutation:
That is, the output of the algorithm has bit 40 of the preoutput block as its first bit, bit 8 as its second bit, and so on, until bit 25 of the preoutput block is the last bit of the output.IP-1 40 8 48 16 56 24 64 32 39 7 47 15 55 23 63 31 38 6 46 14 54 22 62 30 37 5 45 13 53 21 61 29 36 4 44 12 52 20 60 28 35 3 43 11 51 19 59 27 34 2 42 10 50 18 58 26 33 1 41 9 49 17 57 25
The computation which uses the permuted input block as its input to produce the preoutput block consists, but for a final interchange of blocks, of 16 iterations of a calculation that is described below in terms of the cipher function f which operates on two blocks, one of 32 bits and one of 48 bits, and produces a block of 32 bits.
Let the 64 bits of the input block to an iteration consist of a 32 bit block L followed by a 32 bit block R. Using the notation defined in the introduction, the input block is then LR.
Let K be a block of 48 bits chosen from the 64-bit key. Then the output L'R' of an iteration with input LR is defined by:
(1) L' = R
R' = L(+)f(R,K)
where (+) denotes bit-by-bit addition modulo 2.
As remarked before, the input of the first iteration of the calculation is the permuted input block. If L'R' is the output of the 16th iteration then R'L' is the preoutput block. At each iteration a different block K of key bits is chosen from the 64-bit key designated by KEY.
With more notation we can describe the iterations of the computation in more detail. Let KS be a function which takes an integer n in the range from 1 to 16 and a 64-bit block KEY as input and yields as output a 48-bit block Kn which is a permuted selection of bits from KEY. That is
(2) Kn = KS(n,KEY)with Kn determined by the bits in 48 distinct bit positions of KEY. KS is called the key schedule because the block K used in the n'th iteration of (1) is the block Kn determined by (2).
As before, let the permuted input block be LR. Finally, let L() and R() be respectively L and R and let Ln and Rn be respectively L' and R' of (1) when L and R are respectively Ln-1 and Rn-1 and K is Kn; that is, when n is in the range from 1 to 16,
(3) Ln = Rn-1
Rnn = Ln-1(+)f(Rn-1,Kn)
The preoutput block is then R16L16.
The key schedule KS of the algorithm is described in detail in the Appendix. The key schedule produces the 16 Kn which are required for the algorithm.
Deciphering
The permutation IP-1 applied to the preoutput block is the inverse of the initial permutation IP applied to the input. Further, from (1) it follows that:
(4) R = L'
L = R' (+) f(L',K)
Consequently, to decipher it is only necessary to apply the very same algorithm to an enciphered message block, taking care that at each iteration of the computation the same block of key bits K is used during decipherment as was used during the encipherment of the block. Using the notation of the previous section, this can be expressed by the equations:
(5) Rn-1 = Ln
Ln-1 = Rn (+) f(Ln,Kn)
where now R16L16 is the permuted input block for the deciphering
calculation and L() and R() is the preoutput block. That is, for the
decipherment calculation with R16L16 as the permuted input, K16 is used in the first iteration, K15 in the second, and so on, with K1 used in the 16th iteration.
The Cipher Function f
A sketch of the calculation of f(R,K) is given in Figure 2.
, Data Encryption Standard_files/fip46-2.gif)
Figure 2. Calculation of f(R,K).
Let E denote a function which takes a block of 32 bits as input and yields a block of 48 bits as output. Let E be such that the 48 bits of its output, written as 8 blocks of 6 bits each, are obtained by selecting the bits in its inputs in order according to the following table:
E BIT-SELECTION TABLE
32 1 2 3 4 5
4 5 6 7 8 9
8 9 10 11 12 13
12 13 14 15 16 17
16 17 18 19 20 21
20 21 22 23 24 25
24 25 26 27 28 29
28 29 30 31 32 1
Thus the first three bits of E(R) are the bits in positions 32, 1
and 2 of R while the last 2 bits of E(R) are the bits in
positions 32 and 1.
Each of the unique selection functions S1,S2,...,S8, takes a 6-bit block as input and yields a 4-bit block as output and is illustrated by using a table containing the recommended S1:
S1
Column Number
Row
No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
0 14 4 13 1 2 15 11 8 3 10 6 12 5 9 0 7
1 0 15 7 4 14 2 13 1 10 6 12 11 9 5 3 8
2 4 1 14 8 13 6 2 11 15 12 9 7 3 10 5 0
3 15 12 8 2 4 9 1 7 5 11 3 14 10 0 6 13
If S1 is the function defined in
this table and B is a block of 6 bits, then S1(B)is determined as follows: The first and last bits
of B represent in base 2 a number in the range 0 to 3. Let that number
be i. The middle 4 bits of B represent in base 2 a number in the
range 0 to 15. Let that number be j. Look up in the table the number in
the i'th row and j'th column. It is a number in the range 0 to 15 and is
uniquely represented by a 4 bit block. That block is the output S1(B) of S1 for
the input B. For example, for input 011011 the row is 01, that is row
1, and the column is determined by 1101, that is column 13. In row 1 column 13
appears 5 so that the output is 0101. Selection functions S1,S2,...,S8 of the algorithm appear in the Appendix.
The permutation function P yields a 32-bit output from a 32-bit input by permuting the bits of the input block. Such a function is defined by the following table:
P
16 7 20 21
29 12 28 17
1 15 23 26
5 18 31 10
2 8 24 14
32 27 3 9
19 13 30 6
22 11 4 25
The output P(L) for the function P defined by this table
is obtained from the input L by taking the 16th bit of L as the
first bit of P(L), the 7th bit as the second bit of P(L), and so
on until the 25th bit of L is taken as the 32nd bit of P(L). The
permutation function P of the algorithm is repeated in the Appendix.
Now let S1,...,S8 be eight distinct selection functions, let P be the permutation function and let E be the function defined above.
To define f(R,K) we first define B1,...,B8 to be blocks of 6 bits each for which
(6) B1B2...B8 = K(+)E(R)The block f(R,K) is then defined to be
(7) P(S1(B1)S2(B2)...S 8(B8))Thus K(+)E(R) is first divided into the 8 blocks as indicated in (6). Then each Bi is taken as an input to Si and the 8 blocks (S1(B1)S2(B2)...S
PRIMITIVE FUNCTIONS FOR THE DATA ENCRYPTION ALGORITHM
The choice of the primitive functions KS, S1,...,S8 and P is critical to the strength of an encipherment resulting from the algorithm. Specified below is the recommended set of functions, describing S1,...,S8 and P in the same way they are described in the algorithm. For the interpretation of the tables describing these functions, see the discussion in the body of the algorithm.
The primitive functions S1,...,S8 are:
S1
14 4 13 1 2 15 11 8 3 10 6 12 5 9 0 7
O 15 7 4 14 2 13 1 10 6 12 11 9 5 3 8
4 1 14 8 13 6 2 11 15 12 9 7 3 10 5 0
15 12 8 2 4 9 1 7 5 11 3 14 10 O 6 13
S2
15 1 8 14 6 11 3 4 9 7 2 13 12 O 5 10
3 13 4 7 15 2 8 14 12 0 1 10 6 9 11 5
0 14 7 11 10 4 13 1 5 8 12 6 9 3 2 15
13 8 10 1 3 15 4 2 11 6 7 12 0 5 14 9
S3
10 0 9 14 6 3 15 5 1 13 12 7 11 4 2 8
13 7 O 9 3 4 6 10 2 8 5 14 12 11 15 1
13 6 4 9 8 15 3 0 11 1 2 12 5 10 14 7
1 10 13 0 6 9 8 7 4 15 14 3 11 5 2 12
S4
7 13 14 3 0 6 9 10 1 2 8 5 11 12 4 15
13 8 11 5 6 15 O 3 4 7 2 12 1 10 14 9
10 6 9 0 12 11 7 13 15 1 3 14 5 2 8 4
3 15 O 6 10 1 13 8 9 4 5 11 12 7 2 14
S5
2 12 4 1 7 10 11 6 8 5 3 15 13 O 14 9
14 11 2 12 4 7 13 1 5 0 15 10 3 9 8 6
4 2 1 11 10 13 7 8 15 9 12 5 6 3 O 14
11 8 12 7 1 14 2 13 6 15 O 9 10 4 5 3
S6
12 1 10 15 9 2 6 8 O 13 3 4 14 7 5 11
10 15 4 2 7 12 9 5 6 1 13 14 O 11 3 8
9 14 15 5 2 8 12 3 7 0 4 10 1 13 11 6
4 3 2 12 9 5 15 10 11 14 1 7 6 0 8 13
S7
4 11 2 14 15 0 8 13 3 12 9 7 5 10 6 1
13 0 11 7 4 9 1 10 14 3 5 12 2 15 8 6
1 4 11 13 12 3 7 14 10 15 6 8 0 5 9 2
6 11 13 8 1 4 10 7 9 5 0 15 14 2 3 12
S8
13 2 8 4 6 15 11 1 10 9 3 14 5 0 12 7
1 15 13 8 10 3 7 4 12 5 6 11 0 14 9 2
7 11 4 1 9 12 14 2 0 6 10 13 15 3 5 8
2 1 14 7 4 10 8 13 15 12 9 0 3 5 6 11
The primitive function P is: 16 7 20 21
29 12 28 17
1 15 23 26
5 18 31 10
2 8 24 14
32 27 3 9
19 13 30 6
22 11 4 25
Recall that Kn, for 1<=
n <= 16, is the block of 48 bits in (2) of the algorithm. Hence, to
describe KS, it is sufficient to describe the calculation of
Kn from KEY for n = 1,
2,..., 16. That calculation is illustrated in Figure 3. To complete the
definition of KS it is therefore sufficient to describe the two
permuted choices, as well as the schedule of left shifts. One bit in each
8-bit byte of the KEY may be utilized for error detection in key
generation, distribution and storage. Bits 8, 16,..., 64 are for use in
assuring that each byte is of odd parity.
Permuted choice 1 is determined by the following table:
PC-1
57 49 41 33 25 17 9
1 58 50 42 34 26 18
10 2 59 51 43 35 27
19 11 3 60 52 44 36
63 55 47 39 31 23 15
7 62 54 46 38 30 22
14 6 61 53 45 37 29
21 13 5 28 20 12 4
The table has been divided into two parts, with the first part
determining how the bits of C() are
chosen, and the second part determining how the bits of D() are chosen. The bits of KEY are numbered 1
through 64. The bits of C() are
respectively bits 57, 49, 41,..., 44 and 36 of KEY, with the bits of
D() being bits 63, 55, 47,..., 12 and 4
of KEY.
With C() and D() defined, we now define how the blocks Cn and Dn are obtained from the blocks Cn-1 and Dn-1, respectively, for n = 1, 2,..., 16. That is accomplished by adhering to the following schedule of left shifts of the individual blocks:
, Data Encryption Standard_files/fip46-3.gif)
Figure 3. Key schedule calculation.
Iteration Number of
Number Left Shifts
1 1
2 1
3 2
4 2
5 2
6 2
7 2
8 2
9 1
10 2
11 2
12 2
13 2
14 2
15 2
16 1
For example, C3 and D3 are obtained from C2 and D2,
respectively, by two left shifts, and C16 and D16 are
obtained from C15 and D15, respectively, by one left shift. In all cases, by
a single left shift is meant a rotation of the bits one place to the left, so
that after one left shift the bits in the 28 positions are the bits that were
previously in positions 2, 3,..., 28, 1.
Permuted choice 2 is determined by the following table:
PC-2
14 17 11 24 1 5
3 28 15 6 21 10
23 19 12 4 26 8
16 7 27 20 13 2
41 52 31 37 47 55
30 40 51 45 33 48
44 49 39 56 34 53
46 42 50 36 29 32
Therefore, the first bit of Kn is
the 14th bit of CnDn, the second bit the 17th, and so on with the 47th
bit the 29th, and the 48th bit the 32nd.
FIPS PUB 46-2
FEDERAL INFORMATION
PROCESSING STANDARDS
PUBLICATION
1993 December 30
U.S. DEPARTMENT OF COMMERCE/National
Institute of Standards and Technology
DATA ENCRYPTION STANDARD (DES)
U.S. DEPARTMENT OF
COMMERCE, Ronald H. Brown, SecretaryTechnology Administration, Mary L. Good, Undersecretary for Technlogy
National Institute of Standards and Technology, Arati Prabhakar, Director
Comments concerning Federal Information Processing Standards Publications are welcomed and should be addressed to the Director, Institute for Computer Sciences and Technology, National Bureau of Standards, Gaithersburg, MD 20899.
James H. Burrows, Director
Institute for Computer Sciences and Technology
Key words: computer security; data encryption standard; encryption; Federal Information Processing Standard (FIPS); security.
Home Page